TrolMaster Aqua-X NFS-1 Setup: Modules, Pumps, Valves, Sensors, and the App, Step by Step

TrolMaster Aqua-X NFS-1 Setup: Modules, Pumps, Valves, Sensors, and the App, Step by Step

The TrolMaster Aqua-X is a modular irrigation controller. The box gets you a controller and a water detector, and the rest of the system, the modules, the probes, the valves, depends on how many zones you run. That flexibility is what makes the setup confusing the first time.

This guide walks through the NFS-1 in the order you should do it: plan the zones, power the controller, chain the modules, connect valves and pumps, add the sensors, link the app, and program the timers. The specs come from the manufacturer's NFS-1 documentation. Where the documentation doesn't say, we say so, and tell you to check the manual in the box.

The 30-Second Answer

The limits: up to five control modules and 30 outputs per controller, up to 8 water content sensors, and up to 25 water detectors. The modules: the OA6-24 ($93.67) drives six 24 V solenoids under 0.2 A, the OA6-110 ($102.50) drives six small pumps or valves under 1.5 A. The controller: the NFS-1 set is $325.63 with a water detector included. The cost: the controller side alone runs about $70 per zone at 6 zones and about $26 per zone at 30, before valves and sensors. The warning: label every output before you program anything, because mislabeled outputs invert irrigation logic.

Step 1: Plan Your Zones and Label the Outputs

A zone is one valve or one pump on a timer. Decide how many you need first, because it sets how many modules you buy. The NFS-1 takes up to five modules in any mix, with six outlets on each, for a maximum of 30 outputs. Before you wire anything, write down which output goes to which physical zone, and label both ends. The most common cause of over- or under-watering after installation is a mislabeled output, and it is easy to avoid with a marker.

Step 2: Choose the Modules

Module What it drives, per the manufacturer Price
OA6-24, 24 V board Six outlets, each with its own timer, for 24 V devices under 0.2 A, such as solenoid valves. Includes a master pump link option. $93.67
OA6-110, 110 V board Six separately controlled 120 V outlets for small submersible pumps or valves under 1.5 A each. $102.50
DSP-1 / DSP-2 program station Devices up to 10 A (DSP-1 at 120 V or less, DSP-2 at 240 V or less). Works as a multi-function timer. Ask us

The honest check here is current draw. A 24 V solenoid needs to stay under the 0.2 A rating of the OA6-24. For example, the Netafim Series 80 globe valve ($44.11) lists a 24 VAC solenoid with 0.220 A inrush and 0.095 A holding current. The inrush figure is just above 0.2 A, so check the valve's electrical specs against the board before you order a stack of them, or ask us to confirm with the manufacturers.

Step 3: Power the Controller and Chain the Modules

The NFS-1 set includes the controller, a 12 V power adapter, a WD-1 water detector, a 16 foot RJ12 cable, an RJ12 T-splitter, and a touch spot. Modules and sensors connect with standard RJ12 cables, daisy-chained through splitters, or through the SPH-1 8-port hub as an alternative. Plug in the power adapter, then connect modules to the controller one at a time. A 35 foot RJ12 cable coil is $23.94 if you need more reach. Keep power off the 24 V and 110 V outputs until the labels and the wiring are checked.

Aqua-X Controller Cost per Zone NFS-1 plus OA6-24 modules, before valves, pumps, and sensors $70 6 zones $419 total $43 12 zones $513 total $29 24 zones $700 total $26 30 zones $794 total
Controller-side cost per zone: one NFS-1 set at $325.63 plus the OA6-24 modules needed at six outlets each. Valves, pumps, and sensors are extra.

The chart shows why the controller side gets cheaper per zone as you grow: the controller is a fixed cost, and each extra module adds six zones for $93.67. At six zones it is about $70 per zone, at 12 about $43, and at 30, the maximum, about $26. Valves are a separate and larger cost, so price those before you settle on a zone count.

Step 4: Connect Valves and Pumps

Wire each solenoid valve to its labeled OA6-24 outlet, and each small pump to an OA6-110 outlet. For a central pump that should run whenever any valve opens, the OA6-24 has a master pump link that starts a pump automatically when any 24 V solenoid activates, and a DSP module paired this way counts as one module. For anything above the module ratings, use a DSP program station. Follow local electrical code on every connection, and cut power before you touch a terminal.

Step 5: Add the Sensors

The sensor board is the AMP-2 ($112.87), which connects the pH and EC/temperature probes. For an open reservoir, use the PPH-1 pH probe ($82.38) and the PCT-1 EC/temperature probe ($67.99). For probes installed in PVC lines, use the inline versions, the PPH-2 ($184.39) and PCT-2 ($204.99). Calibrate both at the start of each cycle with fresh solution, because drift produces false alerts. Our EC and pH reservoir management guide covers calibration habits.

For the root zone, the controller takes up to 8 water content sensors, which report moisture in the medium. The manufacturer's guidance is to place them at mid-root depth, not at the surface, and to use at least one per variation in media, pot size, or cultivar. The included WD-1 water detector can sit on the floor as a leak detector, or confirm that water arrived after an output fires and alert you if it doesn't.

Step 6: Link the App, Then Program

For internet, the manufacturer recommends a wired network cable from the controller to your router. Download the free TrolMaster app and scan the QR code on the controller, under System, then QR Code. The app gives remote monitoring, settings, and push alerts. The controller does not need the internet to run: saved schedules and sensor triggers keep working offline.

Each output has its own timer. You can run it as a recycling timer or at set times of day with set durations, with up to 12 customizable daily schedules, on times as short as 1 second, and off times as short as 1 minute. Set min and max limits for pH, EC, and temperature so you get alerts when they drift.

Test every output by hand: before you trust a program, force each output on from the controller and walk the room to confirm the right valve opened and the right plants got water.

Where This Fits

If you are building drip lines for this controller, read our Netafim drip stake setup guide first, since the zone math decides how many outputs you need. If you want to tie lights and climate into the same control family, the Hydro-X side is a separate controller; our Hydro-X guide covers it. For a larger facility, ModernFarms finances projects over $25,000 for licensed operators; our financing guide explains what we can and can't tell you about terms.

Start the conversation

Tell us your zone count, valve model, and whether you irrigate from a reservoir or inline. Email info@modernfarms.store or call 818-504-8165, and we'll put together the module and sensor list that fits.

TrolMaster Aqua-X Controller with Water Detector Set (NFS-1) - $325.63 Shop now
TrolMaster Aqua-X 24 V Control Board (OA6-24) - $93.67 Shop now
TrolMaster Aqua-X 110 V Control Board (OA6-110) - $102.50 Shop now
TrolMaster Aqua-X Sensor Board (AMP-2) - $112.87 Shop now
TrolMaster Aqua-X Reservoir EC/Temp Sensor (PCT-1) - $67.99 Shop now
TrolMaster Reservoir pH Sensor (PPH-1) - $82.38 Shop now

Frequently Asked Questions

How many zones can one Aqua-X NFS-1 run?

Up to 30 outputs, per the manufacturer. That is up to five control modules, each with six outlets. Modules can be 24 V solenoid boards (OA6-24), 110 V pump boards (OA6-110), or DSP program stations, in any combination.

What can each module drive?

The OA6-24 is listed for 24 V devices under 0.2 A, such as solenoid valves. The OA6-110 is listed for small pumps or valves under 1.5 A per outlet. The DSP-1 and DSP-2 program stations handle devices up to 10 A.

Does the Aqua-X need internet to run?

No. Saved schedules and sensor triggers keep running without it. Internet is needed for remote monitoring and push alerts. The manufacturer recommends a wired CAT 5 or 6 cable to your router.

How do I connect the app?

Download the free TrolMaster app and scan the QR code on the controller, found under System, then QR Code, per the manufacturer.

How short can a watering event be?

The timers can run as short as 1 second on and 1 minute off. They can recycle or run at set times, with up to 12 customizable daily schedules.

Do I need to calibrate the pH and EC probes?

Yes. Calibrate pH and EC probes at the start of each crop cycle with fresh solution. An uncalibrated probe produces false alerts, which makes automation hard to trust.

What is the difference between the NFS-1 and the larger Aqua-X models?

The NFS-1 is the entry controller in this family. If you need many sensors or more advanced irrigation logic, ask us about the larger Aqua-X models. We can compare specs for your room.

Can I finance equipment for a larger facility?

Financing is available for projects over $25,000 for licensed facilities. A controller won't reach that, but it can be part of a larger order. Rates and terms are not published, so ask in writing.

This article is general information, not technical, financial, or legal advice. Module limits, ratings, and setup details come from the manufacturer's NFS-1 documentation, and we recommend following the manual in the box and local electrical code. Prices and stock reflect ModernFarms' live catalog as of October 14, 2026. We don't upsell, and we'd rather you confirm a valve's current draw than find out the hard way.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.