Hydroponic nutrient mixing order

Hydroponic Nutrient Mixing Order: Why Silica Goes First, and When It Doesn't

You forgot the silica, so you pour it into a reservoir that already holds cal-mag and both base parts. The water goes hazy, and the pH you just set is suddenly too high. Nothing is wrong with the bottles. The order was wrong, and the fix costs nothing but a few minutes of stirring on the next batch.

Short answer: fill with water first. Add silica to the plain water and mix it in. Add cal-mag next if your water and your base nutrient call for it. Add base nutrients one part at a time, mixing between each. Add additives. Read EC, then adjust pH last. Two exceptions matter: the label on your bottle beats any generic list, and a stabilized silicic acid such as PowerSi removes the main reason for "silica first" without changing where we would still put it.

The default mixing order, step by step

This sequence works for most liquid two-part and three-part bases. Each step has a reason, and knowing the reason is what lets you handle a product that does not fit the list.

  1. Water first, close to final volume. Bluelab's rule is to always add nutrients to water, because adding water to concentrated nutrients creates small zones of extreme concentration. Never pour two concentrates into the same cup or into each other.
  2. Silica. General Hydroponics tells growers to add Armor Si to fresh irrigation water before adding base nutrients or other supplements. Mix it until it is fully dispersed.
  3. Cal-mag, if you use it. It goes in after silica and before the base. GH's application notes, reproduced on our CALiMAGic listing, say to add Armor Si first when using both, and to add both before FloraMicro.
  4. Base nutrients, one part at a time. Part A, mix, then Part B, mix. For a three-part base, follow the sequence on the maker's feed chart.
  5. Additives, one at a time, after the base is fully diluted. Bluelab's sequence puts additives only after base nutrients are fully diluted.
  6. EC, then pH. Measure EC and correct strength first, because every addition moves pH. Adjust pH last.

If you run a reservoir that sits for days, our EC and pH reservoir management guide covers top-offs, drift, and change schedules. This post sticks to the mixing itself.

Why order matters: calcium meets phosphate and sulfate

Most mixing problems come down to one reaction. Purdue Extension's guidance for growers is blunt: fertilizer sources containing calcium, phosphorus and sulfate should not be mixed together, because calcium nitrate combined with phosphorus sources forms insoluble calcium phosphate, and combined with magnesium sulfate or potassium sulfate forms calcium sulfate.

That is the whole reason two-part bases exist. As Bluelab puts it, calcium reacting with phosphates or sulfates can form insoluble compounds at high concentration, and an A and B system keeps them apart until dilution makes them safe. Once both parts are diluted in a full reservoir, they coexist fine.

Cal-mag is a calcium product. CALiMAGic's guaranteed analysis is 1-0-0 with 5.0% calcium and 1.5% magnesium, and Botanicare Cal-Mag Plus is 2-0-0 with 3.2% calcium and 1.2% magnesium. Pour it into a small volume of water that just took a heavy dose of a phosphate or sulfate part, and you recreate the reaction the A and B split was designed to prevent. Calcium that comes out of solution is calcium your roots do not get. Putting cal-mag into plain water before the base, and mixing well, keeps it dilute when the base arrives.

"Silica first" is really a potassium silicate rule

Most silica sold for hydroponics is potassium silicate, and potassium silicate is strongly alkaline. The Armor Si label says it plainly: Armor Si is a powerful base (extremely alkaline) and it will raise nutrient pH. Its analysis is 0-0-4, and it contains 10% silicon dioxide derived from potassium silicate. An article in Greenhouse Canada notes that potassium silicate has a pH above 10.

That alkalinity creates two problems if silica goes in late:

The same write-up gives a clear order for basic silicates: add the silicate first, then your lowest pH fertilizer concentrate, then your calcium-containing concentrate. That matches the GH label, which reads add Armor Si to fresh water first, stir while adding, next add fertilizer, then check and adjust pH to 5.5 to 6.5.

Dose matters as much as order. GH lists 1 to 2 mL per gallon as the standard Armor Si rate, with up to 5 mL per gallon only if your program and plants can tolerate it. More silica than the label means more pH correction and a higher chance of polymerization, not more benefit.

Where stabilized silicic acid (PowerSi) fits

PowerSi is sold as stabilized silicic acid rather than potassium silicate, and its maker claims it doesn't raise the pH of your water. The same feed chart's mixing instruction is to add clean water before any other nutrient. It does not demand a silica-first slot.

So the pH reason for silica first mostly goes away with PowerSi. We would still add it first, right after the water. The polymerization risk described above applies to any silicon source once it meets concentrated calcium and magnesium, and putting PowerSi in first costs you nothing. Treat it like any other silica in the sequence, and you never have to remember which product gets which rule.

One honest counterpoint. The same source argues that acid-stabilized silicon sources are not more plant available than properly diluted silicate. The practical case for PowerSi is handling: no pH jump to chase, which matters most in recirculating systems and for growers tired of correcting pH after every silica dose. If you mix by hand, in order, and correct pH at the end anyway, potassium silicate does the job for less money. Our silica cost comparison runs the per-liter numbers.

Where cal-mag goes, and when the label moves it

The default slot is after silica and before the base. Two common labels make this more specific.

CANNA CALMAG AGENT is a water conditioner, not a booster. CANNA calls it a special concentrate for buffering soft water, and the directions are to fill the reservoir, then add 0.1 to 0.5 mL per liter until you reach an EC of 0.4 mS/cm. Base nutrients and additives come after. CANNA treats water below 0.4 EC as soft, and for poor tap water it suggests blending RO and tap to EC 0.2, then using CALMAG AGENT to bring it to 0.4.

Worked example: a 10 gallon reservoir is about 37.9 liters. At 0.1 to 0.5 mL per liter, that is roughly 4 to 19 mL of CALMAG AGENT. With pure RO water, which starts near zero EC, expect to land toward the top of that range. Stop at EC 0.4 whatever the syringe says, then add the base and read EC again.

General Hydroponics puts silica ahead of cal-mag. Armor Si first, CALiMAGic second, then FloraMicro. That is the same order as our default, which is no accident: the silicate goes in while the water is still plain.

Botanicare's Cal-Mag Plus label gives no order relative to other products. It says to mix well and adjust pH accordingly, so use the default slot. For Advanced Nutrients Sensi Cal-Mag Xtra or any line that publishes its own sequence, follow that label over this article.

Whether you need cal-mag at all is a separate question that depends on your water and medium. Our guide on cal-mag for cannabis: when you need it, when you don't works through RO water, coco, and the pH lockout that looks just like a deficiency.

Silica and cal-mag options and what each label says about order

Product Type What the label says about order Our smallest size
PowerSi Original Stabilized silicic acid; maker says it does not raise pH Clean water before any other nutrient 500 mL, $59.99
PowerSi Bloom Silicic acid with plant extracts, for flower Same family; water first 500 mL, $40.02
GH Armor Si (in the CALiMAGic and Armor Si combo) Potassium silicate, 0-0-4, strongly alkaline First, into fresh water, before base and supplements 1 gal each, $59.99 bundle
GH CALiMAGic Cal-mag, 1-0-0, 5.0% Ca, 1.5% Mg After Armor Si, before FloraMicro Quart, $17.31
CANNA CALMAG AGENT Soft water conditioner Into the water first, dose to EC 0.4, then base 1 L, $14.94
Botanicare Cal-Mag Plus Cal-mag, 2-0-0, 3.2% Ca, 1.2% Mg, 0.1% Fe No order given; use the default slot Quart, $14.99
Advanced Nutrients Sensi Cal-Mag Xtra Cal-mag with micronutrients Follow the Advanced Nutrients label for your line 1 L, $10.40

Prices are from our store at the time of writing and will change. If you already run a CANNA or GH base, the matching cal-mag keeps you inside one maker's tested sequence, which is worth more than a few dollars a bottle.

pH and EC go last, mostly

Every bottle shifts pH, silica most of all. Correcting pH after each addition wastes pH Up and Down and leaves you chasing a moving number. Read EC once the solution is complete, correct strength, then set pH.

There is one sanctioned shortcut. General Hydroponics says either way will work, but with a nutrient you have not used before, mix it in, wait 15 to 20 minutes, then check and adjust while tracking how much adjuster you used. Once you know your usual dose for a given water source, you can add the adjuster earlier. GH also notes that RO water typically needs pH Up. For target ranges by medium, see our pH for cannabis guide.

Injectors and stock tanks: order becomes plumbing

At commercial scale, you are not mixing a bucket. You are mixing concentrated stock tanks that an injector doses into the line, so the rules get stricter because everything stays concentrated until injection.

What a bad mix looks like, and the fix

What you see Likely cause What to do
pH jumps right after adding silica Potassium silicate is strongly alkaline Expected. Finish the mix, then correct pH once at the end.
Haze right after cal-mag or a base part goes in Calcium met concentrated phosphate or sulfate before it was dilute Next batch: water near final volume, stir between every bottle, never pre-mix concentrates. If sediment settles, remix.
Haze when silica goes into a finished mix Silica added late, into calcium and acidic base parts Remix with silica first. A slight haze may not hurt plants, but you cannot tell how much silicon is still usable.
pH drifts during the first half hour Solution not finished equilibrating Wait 15 to 20 minutes after mixing, then check and adjust.
EC far above what the label math predicts High-EC source water, or cal-mag added on top of a base that already supplies calcium Test source water EC first. Use cal-mag to reach a target, not by habit.

If every batch behaves and the plants look healthy, your order is fine. Do not rebuild a working routine because a forum post did it differently.

Frequently asked questions

Do you add silica or cal-mag first?

Silica first, into plain water, then cal-mag, then the base. That is the order General Hydroponics gives for Armor Si and CALiMAGic. The one common exception is CANNA CALMAG AGENT, which CANNA treats as a water conditioner dosed into the water to EC 0.4 before the base. If you use silica with it, keep silica first, then CALMAG AGENT.

Can you mix silica and cal-mag together?

In the reservoir, yes, as long as each goes into a full volume of water and is mixed before the next. Never combine the concentrates in a cup or syringe. Concentrated silica meeting concentrated calcium is exactly how silicon polymerizes out of the form plants can use.

Does silica raise pH?

Potassium silicate does. GH labels Armor Si as extremely alkaline and warns it will raise nutrient pH. PowerSi's maker says its stabilized silicic acid does not raise water pH. Either way, set pH after the whole mix is in.

How long should you wait after adding silica?

Long enough to mix it completely. The Armor Si label says to stir while adding, then add fertilizer. It does not specify a wait time. In a reservoir with a pump or a good stir, a few minutes of mixing gets it dispersed before the next bottle goes in.

Do you pH before or after adding nutrients?

After, in most cases. Nutrients move pH, so adjusting first means adjusting twice. GH says either way works once you know your usual adjuster dose. With a new nutrient, mix it, wait 15 to 20 minutes, then check and adjust.

Do LED lights mean I need more cal-mag?

Not automatically. CANNA's take is that no special nutrient formulation is needed for new lights, and a more resilient fix is to raise the rate of a balanced, complete base fertilizer rather than buy an LED-specific bottle. Whether you need cal-mag depends mostly on your water and medium. RO water and soft water are the usual reasons. See our cal-mag guide before adding it by default.

Related guides from Modern Farms

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.